Getting Started with Plumbing Basics for Bathtub Installation
Getting Started with Plumbing Basics for Bathtub Installation
Blog Article
We've unearthed this great article about Tools You Need to Install a New Bathtub down the page on the internet and figured it made good sense to write about it with you on my blog.
Setting up a bath tub isn't precisely rocket science, yet it does require solid plumbing, carpentry, and also often, tiling abilities. Changing an old bath tub with a brand-new one is additionally a moderately hard task. If the old bathtub is readily available, the project can relocate rapidly; if you need to open a wall to eliminate the old tub and also position the new bathtub, the job is a lot harder. In either situation, the project is within a house handyman's skills, although you will require a helper to leave the old tub and also set in the brand-new one. Make certain you have certified on your own for the job and fit attempting it. Rather than working with a specialist to take control of a halfway-completed job, it is much better to think about using one before you begin. Chances are you might require an expert plumber to make tube connections.
This write-up will certainly assist you install a brand-new bathtub in your bathroom if you have actually currently bought a brand-new bathtub as well as don't require to transform the setup of your previous supply of water pipes.
Your tools as well as product checklist should make up the following:
Getting ready for the Installment
First of all, the supporting framework supplied with the bathroom needs to be fitted (if required) according to the producer's instructions. Next, fit the taps or mixer to the tub. When suitable the tap block, it is important to make sure that if the tap comes with a plastic washing machine, it is fitted in between the bathroom and the faucets. On a plastic bathroom, it is additionally reasonable to fit a sustaining plate under the faucets system to avoid strain on the bathtub.
Fit the adaptable faucet connectors to the bottom of both taps making use of 2 nuts as well as olives (in some cases supplied with the tub). Fit the plug-hole electrical outlet by smearing mastic filler round the sink outlet opening, and then pass the electrical outlet through the hole in the bath. Use the nut supplied by the producer to fit the plug-hole. Check out the plug-hole electrical outlet for an inlet on the side for the overflow pipeline.
Next off, fit the end of the flexible overflow pipeline to the overflow outlet. Afterwards, screw the pipe to the overflow face which need to be fitted inside the bath. Make certain you utilize every one of the supplied washers.
Attach the trap to the bottom of the waste electrical outlet on the bathtub by winding the thread of the waste electrical outlet with silicone mastic or PTFE tape, and screw on the trap to the electrical outlet. Attach the bottom of the overflow tube in a similar manner.The bath must now be ready to be fitted in its final setting.
Removing Old Taps
If you need to replace old taps with new ones as a part of your installment, then the first thing you must do is separate the water. After doing so, switch on the faucets to drain pipes any water remaining in the system. The procedure of getting rid of the existing faucets can be fairly bothersome due to the limited accessibility that is typically the situation.
Use a basin wrench (crowsfoot spanner) or a faucet device to reverse the nut that links the supply pipes to the faucets. Have a cloth all set for the staying water that will certainly come from the pipes. When the supply pipelines have actually been eliminated, make use of the exact same tool to loosen up the nut that holds the taps onto the bath/basin. You will certainly need to stop the single taps from turning throughout this procedure. As soon as the faucets have actually been gotten rid of, the holes in the bath/basin will certainly have to be cleaned up of any kind of old securing substance.
Before carrying on to fit the brand-new taps, compare the pipeline connections on the old faucets to the brand-new taps. If the old taps are longer than the brand-new faucets, after that a shank adapter is needed for the new taps to fit.
Setting up the Bath tub
Utilizing the two wooden boards under its feet, place the bath tub in the needed setting. The wooden boards are useful in uniformly spreading out the weight of the bath tub over the location of the boards rather than concentrating all the weight onto 4 little factors.
The next objective is to make sure that the bath tub is leveled all round. This can be accomplished by examining the spirit level and also changing the feet on the tub up until the spirit level reviews degree.
To set up taps, fit all-time low of the furthest flexible tap adapter to the suitable supply pipe by making a compression sign up with; then do the exact same for the various other faucet.
Turn on the water system as well as inspect all joints and new pipework for leaks as well as tighten them if necessary. Fill the bath tub as well as also examine the overflow electrical outlet and also the normal electrical outlet for leaks.
Lastly, take care of the bath paneling as defined in the manufacturer's user's manual. Tiling as well as sealing around the tub should wait till the bath tub has been made use of at the very least once as this will settle it into its last setting.
Suitable New Taps
If the tails of the new faucets are plastic, then you will certainly need a plastic adapter to prevent damage to the string. One end of the connector fits on the plastic tail of the tap as well as the other end provides a link to the existent supply pipes.
If you need to fit a monobloc, after that you will call for minimizing couplers, which attaches the 10mm pipeline of the monobloc to the conventional 15mm supply pipeline.
Next, position the tap in the mounting opening in the bath/basin ensuring that the washers remain in area in between the faucet as well as the sink. Protect the faucet in place with the supplier offered backnut. When the faucet is firmly in place, the supply pipelines can be linked to the tails of the taps. The faucets can either be connected by using corrugated copper piping or with normal faucet ports. The previous kind must be attached to the tap ends first, tightening just by hand. The supply pipes can later be linked to the other end. Tighten up both ends with a spanner after both ends have been attached.
Tiling Around the Bathtub
In the location where the bath meets the ceramic tile, it is needed to secure the joins with a silicone rubber caulking. This is necessary as the fitting can move enough to break an inflexible seal, creating the water to penetrate the wall between the bath and the tiling, causing complications with dampness and also feasible leaks to the ceiling below.
You can select from a variety of coloured sealants to blend in your fixtures and installations. They are offered in tubes as well as cartridges, and can sealing voids as much as a size of 3mm (1/8 inch). If you have a larger space to load, you can fill it with twists of drenched paper or soft rope. Bear in mind to constantly load the tub with water before sealing, to allow for the movement experienced when the bathtub is in usage. The sealant can crack rather early if you do not think about this motion prior to securing.
Alternatively, ceramic coving or quadrant floor tiles can be used to edge the bathroom or shower tray. Plastic strips of coving, which are easy to use and also reduce to size, are additionally conveniently offered on the marketplace. It is advisable to fit the ceramic tiles making use of waterproof or waterproof adhesive as well as cement.
A Step-by-Step Guide to Installing a Bathtub
Is your bathtub looking a bit dated lately? Believe it or not, installing a new one is a project you can do yourself. Whether your bathtub is broken or doesn’t fit in with your current bathroom’s design, you can fix it without having to hire a contractor or paying labour costs.
But, beyond saving money, there are other benefits of installing your own bathtub. When you do this project yourself, you can customise every step of the process. You can also make sure the finished product looks exactly the way you want it to.
This DIY project is quite involved, but by doing some research, preparing your bathroom and using the right equipment, it is definitely one you can take on. This guide will help you understand the technical procedures behind installing a new bathtub.
Remove the Existing Bathtub
To remove the old bathtub, you will need to turn the water supply off before you start any work. After you turn the water off, there will likely still be some water left in your plumbing system, which you can remove by turning on a faucet below the level of the bathtub. Once the water stops running, you are ready to start working.
The easiest way to remove the tub is to remove the faucet, handles and other piping and then pull the tub out from the wall. If this doesn’t work in your situation, you will need to remove part of the wall, remove the piping and then slide the tub out.
Choose the Right Bathtub
The ideal way to replace your bathtub is to find one that has the exact dimensions and has the drain and faucet on the same side as your old one. This way, it will fit in the same place and you won’t have to change the piping system in your bathroom. Choose a tub that matches your home’s decor and fits with the style of the bathroom.
Install the Plumbing and Ledger Board
You can purchase a tub drain kit at a hardware store which will have all the pieces you will need for your new tub’s plumbing. Follow the instructions that came with the kit to install the plumbing in the new tub and then take measurements to make sure the plumbing in the tub will align with the plumbing in your bathroom. If it doesn’t, now is the time to make necessary adjustments.
Some bathtubs need a ledger board that is installed on the wall behind the tub to help support it. If your new bathtub requires one, the directions that came with it will tell you how high it should be installed. If your old bathtub had a ledger board, and it is still in good condition, you can adjust its height to match the new bathtub.
Install the Bathtub
When the plumbing and ledger board are ready, you can install the new bathtub. Carefully lower it into the space, being careful not to damage the tub, wall, plumbing or ledger board. Since bathtubs are very heavy and you will need to line the tub up exactly, it is wise to have someone help you with this step.
Once the tub is in place, it needs to be perfectly level, so use a bubble level instead of estimating how level the tub is. Put the level on the top edge of the tub, not the bottom on the inside, since many tubs are designed with a sloped bottom.
If the bathtub isn’t level, adjust the ledger board and shift the tub until it is. When it is level, use screws to attach the tub to the wall studs. Most bathtubs have pre-drilled holes in the upper flange, so use these but do not over tighten the screws.
Hook up the Plumbing
Now that the bathtub is installed, it needs to be attached to your plumbing system. First, install the shoe fitting under the tub and drain pipe, then the overflow pipe and then the drain flange. Your tub plumbing kit will include specific instructions on how to install these pieces.
Install the Bathtub Surround
A bathtub surround will protect the walls around the tub from water damage and can give your new bathtub a more finished look. To install one, make sure the wall is completely clean and dry so that the adhesive will be able to hold the surround securely. Then, measure the surround and mark the same dimensions on the wall above the tub.
Following the directions that came with the surround adhesive, apply it to the wall. Press the surround against the wall on top of the adhesive and then pull it away for about three minutes to activate the adhesive, then apply the surround again. Keep in mind that this is the most common way to use an adhesive, but you should check the instructions on the package for any special steps.
If there is any excessive adhesive around the sides of the surround, you can use mineral spirits to remove it. Then use masking tape to hold the surround panels in place until the adhesive is dry. Using silicone, seal all the cracks between the surround panels and the gap between the bottom of the panels and the top of the bathtub.
If you want to install tile above your bathtub, instead of a bathtub surround, the process will be very similar. But, you will need to measure and cut tiles and install each one individually, using tile spacers to make sure they are evenly spaced. You will then use grout to fill in the spaces between the tiles.
https://www.hss.com/blog/bathroom/a-step-by-step-guide-to-installing-a-bathtub/
Hopefully you liked our article about How to Install a Bathtub. Thanks for spending some time to browse our post. Sharing is nice. Helping people is fun. I thank you for reading our article about Installing A Bathtub.
Book Services Report this page